New Member With Question!

Discussion in 'Triumph General Discussion' started by Roger Mitchell, Sep 26, 2020.

  1. Roger Mitchell

    Roger Mitchell New Member

    Sep 26, 2020
    11
    3
    Lincoln
    #1 Roger Mitchell, Sep 26, 2020
    I am currently restoring a 1971 TR6R, I am having difficulty removing the swinging arm spindle, I have removed the nut on the right hand side, the left one is stuck fast, using that nut I can turn the shaft fairly freely but cannot get the shaft to come out (having hit the right hand end fairly hard) is it possible that the shaft can only be removed to the right side?

    Thanks,
    Roger....
     
  2. Thripster

    Thripster Elite Member

    Feb 21, 2020
    1,061
    750
    Northampton, UK
    #2 Thripster, Sep 26, 2020
    Cannot help but welcome Roger
     
  3. MadMrB

    MadMrB Elite Member

    Dec 24, 2018
    3,562
    800
    Northamptonshire, UK
    #3 MadMrB, Sep 26, 2020
    Hi and welcome in :)

    I'm sure someone will be along soon who can answer your question.
     
  4. Helmut Visor

    Helmut Visor Only dead fish go with the flow
    Subscriber

    Oct 3, 2018
    6,412
    1,000
    Three Counties
    #4 Helmut Visor, Sep 26, 2020
    Hi Roger
     
  5. Callumity

    Callumity Elite Member

    Feb 25, 2017
    3,362
    800
    Nr Biggar
    #5 Callumity, Sep 26, 2020
    My recollection is that these spindles need pressing out with a hydraulic press or by constructing a puller (not possible without removal of nuts both ends). Hammering is NOT the answer as it just destroys the spindle. A popular mod is then fitting grease nipples on each side bushing so it never needs to come out again!
     
    • Like Like x 1
    • Agree Agree x 1
  6. Roger Mitchell

    Roger Mitchell New Member

    Sep 26, 2020
    11
    3
    Lincoln
    #6 Roger Mitchell, Sep 27, 2020
    Reckon I’ve worked out the problem, when I turn the spindle it’s seized in the spacer in the middle so is also turning the spacer, got to get it pressed out!
    Surprised it’s seized, only been in there 50 years!
     
    • Funny Funny x 3
  7. Yorkshireman

    Yorkshireman Crème de la Crème

    Dec 12, 2015
    3,400
    1,000
    Barnsley
    #7 Yorkshireman, Sep 27, 2020
    Is there room to drill a small hole in the spacer to introduce some penetrating oil, that might ease things when it comes to pressing. It's not unknown to have to apply tons of pressure to move things like that.
    Good luck with the restoration and welcome.
     
    • Like Like x 1
  8. Roger Mitchell

    Roger Mitchell New Member

    Sep 26, 2020
    11
    3
    Lincoln
    #8 Roger Mitchell, Sep 27, 2020
    Spent four hours on it today, tried my hydraulic puller but couldn’t get a straight enough pull to really get the pressure on, reverted to getting the nut off left end of spindle, had totally welded itself on, had to chop the nut up with cutting disc!
    Put loads of stress on the right hand nut and tapped on left, finally managed to get it out - phew
     
    • Like Like x 4
Loading...
Similar Threads - Member Question
  1. SuzukiTri25

    Uk Member Looking At A Thunderbird (lots Of Questions)

    SuzukiTri25, Mar 13, 2019, in forum: Thunderbird
    Replies:
    28
    Views:
    3,845
    dez king
    Dec 13, 2019
  2. crispey

    A Question To Our Italian Members

    crispey, Oct 13, 2018, in forum: Lounge
    Replies:
    0
    Views:
    627
    crispey
    Oct 13, 2018
  3. Sandi T

    To All Los Angeles Forum Members...

    Sandi T, Jan 16, 2025, in forum: Lounge
    Replies:
    1
    Views:
    453
    joe mc donald
    Jan 17, 2025
  4. La_leo

    Thank You Forum Members

    La_leo, Jul 20, 2024, in forum: Bonneville
    Replies:
    7
    Views:
    2,418
    Hitechluddite
    Jul 24, 2024
  5. Boothman

    Trophy Points And Member Status

    Boothman, Sep 14, 2023, in forum: Suggestions & Feedback
    Replies:
    2
    Views:
    916
    Boothman
    Sep 21, 2023

Share This Page

Sign up