HMC_MT's Recent Activity

  1. This site uses cookies. By continuing to use this site, you are agreeing to our use of cookies. Learn More.
  1. HMC_MT replied to the thread Back To The Forum...with A New Mountain Cub.

    @darkman I'm currently having a mild to moderate panic situation here as I abandoned points etc. due to a startling discovery. While...

    May 18, 2022 at 5:34 AM
  2. HMC_MT liked darkman's post in the thread Back To The Forum...with A New Mountain Cub.

    Sorry i misread that question oops, great to its sorted :-)

    May 17, 2022 at 9:10 PM
  3. HMC_MT replied to the thread Back To The Forum...with A New Mountain Cub.

    @darkman see above

    May 17, 2022 at 3:10 AM
  4. HMC_MT attached a file to the thread Back To The Forum...with A New Mountain Cub.

    I was referring to where the non existent wire off the condenser post went but I think I have it sorted. Out the hole where points plate...

    IMG_20220516_152108685.jpg IMG_20220516_152117987_HDR.jpg IMG_20220516_144422375.jpg May 16, 2022 at 10:26 PM
  5. HMC_MT liked darkman's post in the thread Back To The Forum...with A New Mountain Cub.

    A black wire with a white trace should go to the non earth side of your coil.

    May 16, 2022 at 10:21 PM
  6. HMC_MT replied to the thread Back To The Forum...with A New Mountain Cub.

    Yeah I follow him and have watched the Cub videos multiple times. He went with an electronic ignition.

    May 16, 2022 at 7:27 PM
  7. HMC_MT liked GPT100's post in the thread Back To The Forum...with A New Mountain Cub.

    Hi HMC, don`t know if you have seen Paul Brodie on you Tube, he has been assembling a tiger cub engine there might be some info of use.

    May 16, 2022 at 7:27 PM
  8. HMC_MT replied to the thread Back To The Forum...with A New Mountain Cub.

    Where does the other end, end up? I may go to electronic ignition but if I can get this timed and get spark, nothing wrong with points!...

    May 16, 2022 at 5:13 PM
  9. HMC_MT attached a file to the thread Back To The Forum...with A New Mountain Cub.

    An update for @darkman since he's paying attention lol. Got the left and right side together after a few struggles. Was moving on to...

    Screenshot_20220516-093756-566.png May 16, 2022 at 4:43 PM
  10. HMC_MT liked darkman's post in the thread Back To The Forum...with A New Mountain Cub.

    Triumph never used gaskets on the inner covers from new and used Stag Wellseal, works perfectly if applied to both surfaces thinly and...

    May 14, 2022 at 3:57 PM
  11. HMC_MT replied to the thread Back To The Forum...with A New Mountain Cub.

    @darkman my complete gasket set didn't have one for this cover, just the outer cover. Should there be one, or maybe use a gasket maker...

    May 14, 2022 at 5:42 AM
  12. HMC_MT liked darkman's post in the thread Back To The Forum...with A New Mountain Cub.

    The shifter detent pins engage in the cam plate and as long as the pivot pin lines up with the plate and cover to fit the pivot pin...

    May 13, 2022
  13. HMC_MT attached a file to the thread Back To The Forum...with A New Mountain Cub.

    How do I make sure the shift quadrant is correct? My Haynes entertainment manual says nothing about it. [ATTACH] [ATTACH]

    IMG_20220513_094657782.jpg IMG_20220513_094704758_HDR.jpg May 13, 2022
  14. HMC_MT replied to the thread Back To The Forum...with A New Mountain Cub.

    Later today I'll be back inside the left/right side covers to inspect & ad appropriate gaskets. Also slightly worried I may not be...

    May 13, 2022
  15. HMC_MT liked darkman's post in the thread Back To The Forum...with A New Mountain Cub.

    Great to see it all going back together :-)

    May 13, 2022