2018 Speed Triple Rs Fitting Triumph Heated Grips

Discussion in 'Speed Triple' started by komp, Nov 4, 2019.

  1. This site uses cookies. By continuing to use this site, you are agreeing to our use of cookies. Learn More.
  1. komp

    komp Member

    Sep 10, 2019
    44
    18
    essex
    Just about to order up the triumph heated grips for the RS, anyone else fitted these themselves? is it easy enough to do?

    just from previous experience of ordering triumph parts they tend not to come with any instructions.

    I was originally planning to put a spare set of oxford grips that i had on, but as the rubber grip could not be easily removed from the throttle tube decided probably best to just get the official ones.

    cheers
     
  2. Spspeed

    Spspeed Well-Known Member

    Jun 26, 2018
    103
    83
    Michigan
    I've done it on my RS.

    The hardest issue is routing the wires. Took me a bit but my method, in the end, was to use a fishing line tied on a thin 18 gauge electrical wire pushed through the hole in the middle of the bars towards the end. Then remove the wire (used only to guide the fishing line, not for use on the bike) and tie the fishing line to the wiring from the grips and pull it through carefully.
     
    • Like Like x 2
  3. komp

    komp Member

    Sep 10, 2019
    44
    18
    essex
    cheers, sounds fiddly, and the sort of thing I would swear a lot while doing. I will make sure I give myself a few hours to fit!
     
  4. Spspeed

    Spspeed Well-Known Member

    Jun 26, 2018
    103
    83
    Michigan
    Those were indeed my thoughts as I was doing it - I am a DIY guy though and the thought of paying a dealership $90 an hour (and they quoted me 2 hours shop time) just to fit them... yea.... no. I figured it out, they are excellent and I don't regret it for a second.
     
    • Like Like x 1
  5. jeznewsome

    jeznewsome Active Member

    Jun 29, 2016
    61
    28
    Preston, UK
    • Like Like x 3
  6. komp

    komp Member

    Sep 10, 2019
    44
    18
    essex
    great link that. very useful. many thanks
     
  7. Captain Trips

    Captain Trips Member

    Feb 4, 2019
    74
    18
    Surrey, UK
    A word to the wise, start by taking off the right hand side radiator housing so that you can access the connector on the loom. Test the whole kit before you fit it in case of any defects. It can be a right PITA to remove it if one grip fails to work, don't ask me how I know this...
     
    • Like Like x 3
  8. komp

    komp Member

    Sep 10, 2019
    44
    18
    essex
    finally had time to install this weekend. was very straight forward with the instructions provided.
    Had to use some electrical wire to thread the left hand wires, but right hand made its way through on its own.
    the loom connector just twists out of its holder so no need to remove the housing.
    I am very happy with them, look great and work a treat, love the integration with the dash... although doubt ill be out on the triple much until the new year now as salt is already on the roads.
     
    • Like Like x 1
  9. Happy Pants

    Happy Pants New Member

    Jul 12, 2020
    10
    3
    Solihull
    Hi
    I’m just about to order a set of Triumph heated grips for my ST ‘S’ 2019 ... how easy is it to remove the throttle grip? I’ve already read the fitting instructions but it just states refer to the service manual ?
    Cheers
    HP
     
  10. Hubaxe

    Hubaxe Good moaning! aka Mr Wordsalad :)

    Mar 25, 2020
    1,692
    800
    Aix Les bains - French Alps
    insert a screw driver, spray some WD40 or anything equivalent along the gap (the small spraying straw might help), and the throttle grip slips away without effort.
     
    • Like Like x 1
  11. Happy Pants

    Happy Pants New Member

    Jul 12, 2020
    10
    3
    Solihull
    Thanks muchly! :)
     
  12. Happy Pants

    Happy Pants New Member

    Jul 12, 2020
    10
    3
    Solihull
    Thanks muchly!
     
    • Like Like x 1
  13. Snusmumrik

    Snusmumrik Well-Known Member

    Sep 16, 2020
    92
    68
    Switzerland
    I have heated grips installed from factory (I optioned them).
    I have related question:
    I have noticed that I am already wearing out the rubber on left handle, are these rubbers replaceable or do I have to buy a new set of heated grips?
     
  14. komp

    komp Member

    Sep 10, 2019
    44
    18
    essex
    i cannot say for certain, but from what i recall when installing they are just one piece, so very much doubt can just replace the rubber outer.
     
    • Agree Agree x 1
Loading...

Share This Page