Single Sided Stand For The New 1200rs?

Hi, Just ordered a speed triple 1200rs and my dual sided paddock stand isn't going to work so well. can anyone advise whether the new 1200rs takes the same pin diameter as the previous models?

Many thanks

 

The old one is 27.5 mm
Best get out the tape measure to be sure but i'd say a yes.

Single Sided Paddock Stand Pin - 27.5mm OD

https://www.rg-racing.com/browsetype/Paddock_Stand/Triumph/Speed_Triple/PIN6/

 

New one is about 40mm similar to some Ducati models. Ducati stands are stupid money ...

 

Get an Abba stand

 

Abba stand OK but fiddly IMO rear stand loads easier to use. Less risk of accidents

 

1200RS rear padock stand pin is 40mmin dia. The PITA part is having to remove the hub nut locking spring clip thingy to get the stand spindle in then refit it after removing the stand.

Alternatively, as I have just done, spent 15mins with a dremel or equivalent and cut a groove in the paddock stand spindle to accomodate the securing spring clip protrusion. Works a treat.

 

I have also noticed that the rear wheel nut torque is now a massive 230Nm compared to 1050RS 146 Nm . My torque wrench only goes up to 150Nm so just as well I am not in the market for a 1200RS .

 

I'd guess that if you're paying upwards of £15,000 for a new Speed Triple then dropping £50 on a torque wrench is no big deal?

https://www.ebay.co.uk/itm/18507992...MIgNy7styo8wIVpGLmCh1khwt1EAQYECABEgI-zPD_BwE

 

True (plus the new paddock stand, wheel nut socket and rattle gun as my breaker bar would'nt shift that mutha )

 

On the picture it's 40,6 mm and on my invoice 40,7 is mentioned, so lots bigger than the previous model.



Does somebody know where to find a auxiliary cable /plug or something to connect a usb socket?? (Don't want to connect it to the battery directly. Lifted the tank today can't find anything / a blue marked wire.)

 

Does this one actually fit the 1200rs ?

 

They will be the old size I think . Pity they don't put the pin size not just. Various bike ...

 

I have one of these, red. Ducatti size spindle fits. I just cut a small groove into the spidle with a dremel wannabe tool to facilitate the locking spring fitted to the nut.

 

Workshopping.co.uk has a Sealey STW905 Torque Wrench Micrometer Style 1/2"Sq Drive 60-330Nm - Calibrated with lifetime guarantee/warranty for £64 delivered. Just ordered one.

 

Ordered the torque wrench cheers also found this and ordered as a low cost stand https://motorcyclepartswarehouse.co...o1X6gGf5JvNxIeAtj_hU3zbD5iyG2LxhoCuZ0QAvD_BwE

 

Anyone know a supplier for the socket for rear wheel nut removal?

 

Answered my own question 25 quid on Amazon https://www.amazon.co.uk/dp/B0183SWUWQ?psc=1&smid=A3P5ROKL5A1OLE&ref_=chk_typ_imgToDp

Ducati type 55mm 12 point so I believe .. can check once received

 

Hi,

i have a Rs1200 and got that paddock stander.

I put the option for the triumph and the one that came is the 40,6. Fit perfectly in the bike.

I can take some photos (only Thrusday forward) of the paddock stand with the bike if necessary.

Regards,

 

This is a prefect rear wheel nut socket .

 

This stand seems really good for the money !