Oil In Coolant Speed Triple

Discussion in 'Technical Help' started by Merida53, Apr 2, 2023.

  1. Merida53

    Merida53 New Member

    Joined:
    Jun 27, 2022
    Messages:
    3
    Likes Received:
    0
    Trophy Points:
    1
    Location:
    North Yorkshire
    Hi, we have just done an engine rebuild on my 2013 speed triple due to a gearbox problem. Started it and found a large amount of coolant in the oil. I’ve used genuine triumph gaskets and before the rebuild had no problems with coolant in the oil. Apart from the head gasket is there anything else it could be?

    F95C59C6-29FE-4DB8-80B4-5B1C5D713389.jpeg
     
    #1
  2. speeder

    speeder Noble Member

    Joined:
    Jan 3, 2019
    Messages:
    314
    Likes Received:
    409
    Trophy Points:
    313
    Location:
    dorset
    Almost certainly head gasket. A pressure leak down test will confirm.
     
    #2
    • Agree Agree x 1
  3. Samsgrandad

    Samsgrandad Senior Member

    Joined:
    Dec 15, 2019
    Messages:
    600
    Likes Received:
    700
    Trophy Points:
    243
    Location:
    Somerset
    Yes head gasket, when you have it apart, again, make sure that the head and barrels are flat, true and not warped
     
    #3
    • Agree Agree x 2
  4. tcbandituk

    Subscriber

    Joined:
    Apr 8, 2016
    Messages:
    2,180
    Likes Received:
    2,886
    Trophy Points:
    1,000
    Location:
    Reading
    Probably head gasket given you've just rebuilt it.
    But could be a core plug if stored with just water as coolant in freezing temperatures.
     
    #4
  5. Iceman

    Iceman Crème de la Crème

    Joined:
    Apr 19, 2020
    Messages:
    1,620
    Likes Received:
    2,829
    Trophy Points:
    1,000
    Location:
    Lancashire
    AS others have said it does point to the head gasket, however when dismantling the engine often the liners are disturbed, these are sealed at the factory and it only takes a very minor disturbance to the liners and a water leak will occur, it will need stripping back down, checking the head for warping as well, use a good steel rule across the block to check the face, but more importantly tolerances between the liners. Unfortunately a number of speed triples had both gearbox and clutch issues, why on earth Triumph designed the clutch so complex is beyond me, the gearchange return spring behind the clutch is a weak point and was modified for a stronger one (I do have a couple of the genuine Triumph German made ones if you need one). The gearchange mechanism on the shaft has a habit of detaching and falling into the crankcase, it can lead to gearbox failure. One main issue is Triumph use external manufacturers for parts, sometimes they switch to a different supplier mid way through production (supply issues), therefore there is a risk in quality control, it's been like this for years with both car and bike manufacturers. The remedy for the gearchange mechanism is to tack weld it to the shaft, this is a permanent failsafe way to stop this happening.
     
    #5
  6. Merida53

    Merida53 New Member

    Joined:
    Jun 27, 2022
    Messages:
    3
    Likes Received:
    0
    Trophy Points:
    1
    Location:
    North Yorkshire
    If it is the liners, which I suspect it is, how would I reseal the ?
     
    #6
  7. Iceman

    Iceman Crème de la Crème

    Joined:
    Apr 19, 2020
    Messages:
    1,620
    Likes Received:
    2,829
    Trophy Points:
    1,000
    Location:
    Lancashire
    You can use a quality brand silicone sealer such as pro seal RTV, if you go to the bikers toolbox website you will see it, these people are first class and only sell quality products, I have had a number of items over the years and not had an issue.
     
    #7
    • Like Like x 2
Loading...

Share This Page