Fitting heated grips.

Discussion in 'Technical Help' started by brybrem, Oct 8, 2013.

Page 2 of 3
  1. brybrem

    brybrem Senior Member

    Mar 8, 2013
    1,433
    113
    North Wales
    #21 brybrem, Oct 12, 2013
    Must admit Dunc, I don't think that even I could fuck this up after your post, thanks. Mind you, let's see what tomorrow brings. x
     
    • Like Like x 2
  2. P19DJG

    P19DJG Banned

    Mar 16, 2013
    1,660
    0
    #22 P19DJG, Oct 12, 2013
    Perhaps have a fire extinguisher or bucket of water ready just in case then Bry x.
     
    • Like Like x 1
  3. brybrem

    brybrem Senior Member

    Mar 8, 2013
    1,433
    113
    North Wales
    #23 brybrem, Oct 12, 2013
    A bucket of water with a possible electrical fire??? Are you mad, sir?
     
  4. P19DJG

    P19DJG Banned

    Mar 16, 2013
    1,660
    0
    #24 P19DJG, Oct 12, 2013
    The fire extinguisher for the electrical fire (dry powder obviously) & the bucket of water for when the garage starts to go up
     
  5. brybrem

    brybrem Senior Member

    Mar 8, 2013
    1,433
    113
    North Wales
    #25 brybrem, Oct 12, 2013
    It's a big garage!
     
  6. P19DJG

    P19DJG Banned

    Mar 16, 2013
    1,660
    0
    #26 P19DJG, Oct 12, 2013
    Fuck the fire extinguisher & the bucket of water then mate... Just make sure you have your trainers on & a clear escape route
     
    • Like Like x 2
  7. Screwball

    Screwball Active Member

    Mar 21, 2013
    1,017
    36
    Kent
    #27 Screwball, Oct 12, 2013
    Last edited: Oct 12, 2013
    That Dunc ain't just a pretty face... Just seen the post and yep if it don't work just use 87a.... It's a normally open(NO)/ normally closed (NC) relay giving you the option of the idle state of the relay.....

    You'd have to be pretty simple to fuck it up after the diagram PIG has done...

    And just so you know what I meant by idle state when power is off, circuit is made and power will flow through 87a. Turn power on and the circuit is now made through 87...
     
    • Like Like x 1
  8. brybrem

    brybrem Senior Member

    Mar 8, 2013
    1,433
    113
    North Wales
    #28 brybrem, Oct 13, 2013
    I think we're all indebted to Gabby Screwball Johnson for his display of genuine frontier gibberish...
     
    • Like Like x 1
  9. P19DJG

    P19DJG Banned

    Mar 16, 2013
    1,660
    0
    #29 P19DJG, Oct 13, 2013
    Just heard some fire engine sirens in the distance, they aint heading towards you are they Bry? :smile:
     
    • Like Like x 1
  10. brybrem

    brybrem Senior Member

    Mar 8, 2013
    1,433
    113
    North Wales
    #30 brybrem, Oct 13, 2013
    Do I need to fit the 5A in line fuse as shown on your diagram? dunno_smilie.gif

    dunno_smilie.gif
     
  11. P19DJG

    P19DJG Banned

    Mar 16, 2013
    1,660
    0
    #31 P19DJG, Oct 13, 2013
    Why you ask?

    1. Dont have one & wanted to check that its definitely required to add to my shopping list
    2. Dont have one, started job & want to finish it BUT cant be arsed to go & get an inline fuse
    3. I dont think it requires the fitting of an inline fuse (even though i know fuck all about electrics & think a bulb is the sun in a bottle)
    4. I think you have made a mistake with the diagram Dunc you fucking retard

    You dont have to fit any fuses anywhere mate, its all about safety, protecting circuits, the bike & the accessories fitted. Personally for the sake of a quid i would but its up to you.
     
    • Like Like x 2
  12. brybrem

    brybrem Senior Member

    Mar 8, 2013
    1,433
    113
    North Wales
    #32 brybrem, Oct 13, 2013
    Number 4, pal - wasn't sure if you'd just 'cut and pasted' from somewhere else and accidentally left it in. I apologise unreservedly for doubting you. x
     
    • Like Like x 1
  13. brybrem

    brybrem Senior Member

    Mar 8, 2013
    1,433
    113
    North Wales
    #33 brybrem, Oct 13, 2013
    Oh, and number one!
     
    • Like Like x 2
  14. mr.h

    mr.h Senior Member

    May 29, 2013
    362
    113
    Lincolnshire
    #34 mr.h, Oct 13, 2013
    So, I've stumbled across this thread - what make of grips are you fitting B? I have fitted them before and can give honest and useful advice on this thread ( makes a change eh! - too wet out here for white boots today) :eek:
     
  15. brybrem

    brybrem Senior Member

    Mar 8, 2013
    1,433
    113
    North Wales
    #35 brybrem, Oct 13, 2013
    Fitting R&Gs. The grips are a bit smaller than the Oxford ones I've had on my previous bikes (which I've always had fitted by dealers in the past at a cost more than the grips themselves!).

    I'm sat at the pc myself at the moment (after being out and getting (TWO) in-line fuse holders and a pack of 5A fuses) writing a Mr. Angry letter to my wife's work - it's either that or going and smacking her boss!
     
    • Like Like x 1
  16. mr.h

    mr.h Senior Member

    May 29, 2013
    362
    113
    Lincolnshire
    #36 mr.h, Oct 13, 2013
    Ah, never fitted the R&G's one B... not much use I'm afraid! lmfao not that you'd expect anything else! But a Mr. Angry letter to the wife's boss? whats gone on fella???? :eek:
     
  17. P19DJG

    P19DJG Banned

    Mar 16, 2013
    1,660
    0
    #37 P19DJG, Oct 13, 2013
    Fuck the letter, nobody reads them or takes any notice. Plus her boss will probably think "what a wanker" her husband wrote me an angry letter.... Well i am pissing my pants! NOT!!!

    However...... A broken jaw or nose is a constant reminder that you perhaps pissed somebody off.

    Whoever said "the pen is mightier than the sword" was a total fucking spineless coward! Where as "actions speak louder than words" gets my vote every time man, its the tried & tested method. View attachment 2035
     
    • Like Like x 1
  18. brybrem

    brybrem Senior Member

    Mar 8, 2013
    1,433
    113
    North Wales
    #38 brybrem, Oct 13, 2013
    I'm writing to HR and her boss's, boss's boss. Basically the man is a fat, gay bully. I tend to agree with you, Dunc, but he's already had a couple of complaints against him and I'm hoping that a third my get him sacked or transferred. Then when he's not her boss any more he'll get his smack - or if they don't do anything about it he'll get smack anyway! QED
     
    • Like Like x 2
  19. brybrem

    brybrem Senior Member

    Mar 8, 2013
    1,433
    113
    North Wales
    #39 brybrem, Oct 21, 2013
    Right! That's fucking it! I fitted the lovely black bars from my old SIII and the new R&G heated grips to my new one, yesterday. After following the perfect instructions from Dunc (Pig) and John (Screwball) I turned the key and everything came on but the ECU didn't make its usual 'just checking' noises. I pulled the clutch in, hit the start button and... nothing. Fuck! So I started pulling out the new connections, one by one, to see if any of them were interfering with the bike's proper electrics and nothing made a difference. As you all know, I abso-fucking-lutely hate electrics, so I ended up ripping the fucking lot out through sheer frustration! The second I did this I noticed that when I put the new bars on I must have inadvertently hit the engine kill switch... The rest is history - I set fire to the garage, stormed into the house, killed the wife, drank her blood, nailed the dog to the door and resigned from my job. Bought a small place in Armenia and that's where I'm posting from now. Perhaps an over reaction but, God, I feel better for it!
     
    • Like Like x 2
  20. P19DJG

    P19DJG Banned

    Mar 16, 2013
    1,660
    0
    #40 P19DJG, Oct 21, 2013
    Oh well, what with you being a complete fucktard, the chances are your wiring of the heated grips, despite having a simpletons diagram to follow, would of probably burnt the place down leading to the horrific death of the wife & the dog anyway.

    Love you x View attachment 2056
     
    • Like Like x 1
Page 2 of 3
Loading...
Similar Threads - Fitting heated grips
  1. komp

    2018 Speed Triple Rs Fitting Triumph Heated Grips

    komp, Nov 4, 2019, in forum: Speed Triple
    Replies:
    13
    Views:
    7,569
    komp
    Nov 18, 2020
  2. Dave Murphy

    2013 Tiger 800 Denali Horn Fitting , Help Needed

    Dave Murphy, Sep 16, 2025 at 10:46 AM, in forum: Technical Help
    Replies:
    1
    Views:
    118
    No1UKnow
    Sep 18, 2025 at 8:49 PM
  3. Junglie25

    Slightly Unusual - Refitting Original Exhaust

    Junglie25, Sep 15, 2025, in forum: Speed Triple
    Replies:
    10
    Views:
    453
    Junglie25
    Sep 16, 2025 at 7:39 AM
  4. Jay Gee

    Fitting Centre Stand To A 2024 Speed Twin 900

    Jay Gee, Jul 22, 2025, in forum: Technical Help
    Replies:
    6
    Views:
    413
    joe mc donald
    Jul 26, 2025
  5. Norfolk Scram

    Scrambler Universal Silencer Fitting To 865 Scrambler.

    Norfolk Scram, Feb 3, 2025, in forum: Thruxton, Scrambler & Trident
    Replies:
    0
    Views:
    273
    Norfolk Scram
    Feb 3, 2025

Share This Page

Sign up